The Chevrolet Suburban can be downloaded HERE!!!
Thanks for all your work Christian.
The Chevrolet Suburban can be downloaded HERE!!!
Thanks for all your work Christian.
Regards, Tom Stovall KRDD
Well, this looks really nice! But for the life of me I can't get the engine to stay running for more than a few seconds (even staying in parked) let alone drive anywhere.
Any suggestions?
The throttle only works when you are in the cab view. I was also trying to get the suburban to move from the spot view. Push the joystick forward from the cab view.
Regards, Tom Stovall KRDD
Hi all reading this,
Unfortunately, a last-minute change in the package caused one file in the package to be corrupted, in an Email transfer between me and Christian.
Which probably explains the problems mentioned in above posts.
Sorry ….
Will be repaired soon.
Rob
Hi Rob - that did cross my mind - my first attempt was at Denver (KDEN - LOTS of lovely flat airport surface but indeed rather high). But then I tried it at a couple of random coastal spots (in Libya, I think) close to sea level, and the result was the same. Don't know if the initial run had somehow 'locked' some altitude setting?
Gary.
The basic problem is that it is a Chevy. If it had been a Ford, it would run perfect.
Running for my Nomex suit, in preparation for the flame posts that are sure to follow.
My computer: ABS Gladiator Gaming PC featuring an Intel 10700F CPU, EVGA CLC-240 AIO cooler (dead fans replaced with Noctua fans), Asus Tuf Gaming B460M Plus motherboard, 16GB DDR4-3000 RAM, 1 TB NVMe SSD, EVGA RTX3070 FTW3 video card, dead EVGA 750 watt power supply replaced with Antec 900 watt PSU.
Hi,
The new FSX release (V101) is available now in the SOH - FSX/Other library.
For simmers who downloaded the original version V100: Delete your folder …/Airplanes/Chevrolet Suburban - FSX/ and all it's content.
To (re-)install: from the new .zip file, copy the folder FSX_Bahrometrix_Chevrolet_Suburban_ZipFile_V101.zi p/Chevrolet Suburban FSX/ and all contents, to your .../Airplanes/ folder.
And then READ the files in your.../Airplanes/V101 should resolve problem with the transmission selector and spontaneous engine shutdown.Chevrolet Suburban FSX/Doc/ folder.
REQUIREMENT NOTES:
1. This FSX version of the addon requires FSX-SP2, FSX-Accel or FSX-Steam.
It MAY work on FSX-RTM or FSX-SP1, but is not supported.
2. This addon requires the presence of the standard Microsoft library "Visual C++ 2015 Redistributable" on your PC.
Without this software library installed, the flightmodel WILL NOT work.
You can check this in Windows, under "Installed Programs". It should contain the entries:
- Microsoft Visual C++ 2015 Redistributable (x86)
and
- Microsoft Visual C++ 2015 Redistributable (x64).
If not installed yet, you can download it here:
https://www.microsoft.com/en-us/down....aspx?id=48145
Works for WindowsXP-SP3 upto Windows10.
It's best to install both the .x86 and .x64 versions.
NOTE: if the 2017 version of this library is allready installed on your PC, it will most probably work too since this should be downward-compatible.
Best regards, Rob
PS: Tom, can you please remove the link in your first post to avoid people downloading the old V100 version ?
PS:
In case anyone wonders:
You don't drive this addon with the usual flightsim Throttle lever/wheel on your stick/yoke/throttle-quadrant.
Please DO read the Quickstart Reference manual …..
Rob
regards
Christian
P3Dv4 - ASUS Z97 Pro i7 4770k@4.4 Ghz (OC) 8 GB Kingston HyperX XMP 1600 Mhz ASUS GTX 1070 STRIX 8GB
Hi Christian and Rob, thanks for the update.
Just tried V1.01 (at KVNC) and the good news is that the engine no longer seems to stall once started.
The not-so-good news is that I can now not move the gear shift out of parked while the engine is running (either by clicking or keyboard). To do so I need to kill the engine, which then will not restart once out of the parked position.
This is with all combinations of the brake being on/off.
Gary.
My computer: ABS Gladiator Gaming PC featuring an Intel 10700F CPU, EVGA CLC-240 AIO cooler (dead fans replaced with Noctua fans), Asus Tuf Gaming B460M Plus motherboard, 16GB DDR4-3000 RAM, 1 TB NVMe SSD, EVGA RTX3070 FTW3 video card, dead EVGA 750 watt power supply replaced with Antec 900 watt PSU.
Suuuper that the car stays on now. We are a step ahead!
You can also use the F5 to F8 keys to select and change gears. Give it a try.
regards
Christian
P3Dv4 - ASUS Z97 Pro i7 4770k@4.4 Ghz (OC) 8 GB Kingston HyperX XMP 1600 Mhz ASUS GTX 1070 STRIX 8GB
Okay - PROGRESS!
It seems nothing I do will move the shift out of parked while the engine is running...
BUT - I have discovered I can turn the engine off, move the stick to neutral, and then start it, after which everything seems to function as it should - as long as I don't put the stick back into parked.
So, I now have a driveable Suburban - which also runs fine even at KDEN.
Thanks!
Now I just need to adapt to driving a car with the steering wheel on the wrong side
Gary.
If you can't get the transmission lever out-of Park position (when the engine is running): you MUST apply Brakes when you move the lever (either with flaps commands, a single keystroke like Shift-D, or mouseclcicks in the VC).
As real as it gets ….LoL
If that doesn't work: What are you using as Brakes ???
By default, it is the lower half of your stick/yoke (so: pull the stick back from Center; see Quickstart Reference).
NOT the usual Brakes key/button command in FSX, since that is NOT a fully contiguous and proportinal brake axis (as modelled in this Chevy).
To check if your throttle and brakes "pedals" are working properly:
- Open the speed/rpm 2D window (Shift-1)
- Observe green bar (throttle pedal) and red bar (brakes pedal).
- Throttle (default): pushing the stick fully forward should make the green bar fully lit.
- Brakes (default): pulling the stick fully back should make red bar fully lit.
So using the default (joystick only) , doesn't allow you to apply both throttle and brakes at the same time (like you can in a real car)
The most realistic way to drive this Chevy addon is with a rudder pedal set, of which you use the toebrakes as throttle pedal (right toebrake) and and brake pedal (left toebrake).
Again, see the QuickStart Reference doc how to configure that in the panel.cfg.
Clear now ???
Rob
"By default, it is the lower half of your stick/yoke"
ah...my misunderstanding. I was trying the VC click and spoiler commands to apply braking for the shift change (which do both cause the vehicle to set the brake), not pulling back on the joystick for shift change at start.
It works!! (just as it probably should).
Good stuff. All fine! Now to go driving.
Gary.
OK, glad it works for you now.
But you may also have missed this:
The Spoiler (or FSX key/button for ParkingBrakes) toggles the Handbrake in the car; which is completely independant from the Brake "pedal" …..
And operationally modelled as such in this addon too(in the 2D RPM gauge this can be seen as a big red H).
But, and here is where it might get confusing:
What is named a "Handbrake" (and operated by a lever) for most cars, is named "ParkingBrake" in the real Chevy Suburban.
Works exactly the same, but in the Chevy it's not a lever, but a seperate footpedal.
Which is animated too in the VC (like the Throttle and Brake pedals are ….).
And did I mention modelled features like on/off switchable TractionControl, AntiBlockingSystem, and CruiseControl ?
(a bit simplyfied implementation now, but they basically work …..)
This addon is not just a great visual model to drive around in the scenery, but also about driving/operating the car systems-wise.
Almost as-real-as-it-gets in Flightsimulator .
Sorry for the "advertising" ...LoL
Best regards, Rob
I've taken a few pieces out and made a very nice AI Suburban and have it running around a few airports. (P3Dv3.5)
Using recent AI vehicles from MAIW, I have also a black Suburban being followed (chased?) by a police car with flashing lights.
regards
Christian
P3Dv4 - ASUS Z97 Pro i7 4770k@4.4 Ghz (OC) 8 GB Kingston HyperX XMP 1600 Mhz ASUS GTX 1070 STRIX 8GB
I love this car
Bookmarks