My own Gary Burns airfield problem

[Ian Astill]

Hi again, sorry for constantly talking about my problems!!

I have tried hard to rectify this myself

So I installed the Gary Burns RAF building (Gsl_Raf_Buildings) and I also installed the BoB pack. On top of that I added the two update packages that he issued recently

Thing is that certain buildings (The belfast hangers and the TJ and T2 hangars) will not die! Rockets, bombs, cannon all pass straight through them. Now the only thing I can think of is that there is a clash somewhere as the two sets seem to overlap

Looking at my mdlnames file I have the following entries for them

"Barracks1"=Barracks, RAF Barracks Block-Gary20
"Belfast1"=Hangar, RAF Belfast Single Bay Hangar-Gary20
"Belfast2"=Hangar, RAF Belfast Double Bay Hangar-Gary20
"Belfast3"=Hangar, RAF Belfast Tripple Bay Hangar-Gary20
"Bellman"=Hangar, RAF British Bellman Hangar
"Bicester"=Building, RAF British Operations Block
"BlastPen"=Blastpen, RAF Brick-Gary20
"BlastPen1"=Blastpen, RAF Bunker-Gary20
"BlastpenClosed"=Revetment, Blastpen, RAF British (Closed)
"BlastpenOpen"=Revetment, Blastpen, RAF British (Open)
"Blister"=Hangar, RAF Blister Type Hangar-Gary20
"ChainTower"=Tower, RAF Radar Tower-Gary20
"Chute"=Building, RAF Parachute Stores-Gary20
"Dispersal"=Building, RAF Dispersal Hut-Gary20
"Duxhut1"=Building, RAF British Long Hut"
"Latrines"=Building, RAF Latrine Hut-Gary20
"Mobstore"=Building, RAF Mob Store-Gary20
"mw_tree"=Tree, British Tree
"Nissen"=Building, RAF Nissen Hut-Gary20
"T2Hangar"=Hangar, RAF T2 Type Hangar-Gary20
"TJHangar"=Hangar, RAF TJ Type Hangar-Gary20
"TowerWith"=Builiding, RAF Watch Office 12779/41 - Tower-Gary20
"TowerWithout"=Building, RAF Watch Office 12779/41 - No Tower-Gary20
"WMTower"=Building, RAF Watch Office 5845/39-Gary20
"Blister"=RAF Blister Type Hangar
"Chute"=RAF Parachute Stores
"Dispersal"=RAF Dispersal Hut
"Latrines"=RAF Latrine Hut
"Nissen"=RAF Nissen Hut
"T2Hangar"=RAF T2 Type Hangar
"TJHangar"=RAF TJ Type Hangar
"WMTower"=RAF Watch Office 5845/39
"TowerWith"=RAF Watch Office 12779/41 - Tower
"TowerWithout"=RAF Watch Office 12779/41 - No Tower
"Belfast1"=RAF Belfast 1 Bay Hangar
"Belfast2"=RAF Belfast 2 Bay Hangar
"Belfast3"=RAF Belfast 3 Bay Hangar
"BlastPen"=RAF Brick Blastpen
"BlastPen1"=RAF Bunker Blastpen
"Barracks1"=RAF Barracks Block
"Mobstore"=RAF Mob Store
"ChainTower"=RAF Radar Tower

Obv there are a few overlaps, Do I need to change some of the names in the brackets? and if so are there any knock on effects I should look out for?

Thanks for being patient with me

[kdriver]

Hi again Ian,

Did you install the recent update by Pen32Win? He fixed that and some other problems.

Kevin

[sc7500]

...Did you install the recent update by Pen32Win? He fixed that and some other problems....

I had similar challenges that were repaired with the installation of Pen's new BGLs.

Still having a small issue with directionality - some hangars don't take damage from certain angles, could be a DP file damage box size deal.......

SC
:kilroy:

[Ian Astill]

I've installed both of the update packages, still no joy