CFS3
Oh yes, same type just a different wrapping - see as soon as it is approved.
Oh, Santa another present?
Oh yes, same type just a different wrapping - see as soon as it is approved.
Waiting anxiously...
Hello - just checked and it is there - under the tree with the other one.
Ok, found the file! Super awesome work...were these intended for OFF originally?
I wanted to .....
I contacted the OFF folks and shared the planes, but they have restrictive policies on the planes they use (and they should) and they were not willing to partner the way I wanted. I get it and it is their show so we could not strike a deal. They liked the external and asked for some other changes... Just wish I could find a way to use these in OFF so folks could at least fly them against other WW1 planes. I thought that there was a way to do that, but we'll need to wait a see...shame really. I wanted to see what the SSW could do as it was reported to be a very good late war plane.
Ted
Well we thank you for your efforts at any rate Ted, it's a really nice airplane! I hope someone will be able to figure out how to add it to OFF/WOFF at some point so it can be enjoyed to its fullest against real opponents.
Thanks Ted,i will give them a go against my beautiful hobbit special. I have all the OFF/WOFF files in my advanced CFS3 set up.
They are really nice, will post some screenshots (as i can)battling them with my Hobbit special.
I bought OFF when it came out and then did away with the new user interface and went back to a conventional CFS3 like set-up dedicated to WWI planes, locations and scenarios. For me, it's very easy to add new planes, so thank you very much for these.
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
These two seem to be unflyable. The CG seems all out of whack, and I often get control reversals.
Is anyone else have trouble with achieving straight and level in them?
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
Fly fine on my rig. Let me know and I'll fix if there is problem.
Okay, I'll check my joystick set-up.
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
Recalibration helped some. What helped more was to apply up elevator trim. Even so, it's a pretty twitchy ride, and easily subject to PIO.
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
Work Fine here, except for the lack of a seat belt that is.
Will it instal in Between heaven and Hell and could you go back to the CFS3 SETUP. I must admit I prefer the old cf3 setup where you can addon planes without upsetting anything.
Can't seem to find this one where is it?Originally Posted by phrog_phixer
Excellent work, as usual. Very grateful to have both aircraft. Many thanks.
With further flying I'm finding that once the elevator trim is adjusted it's fairly good except for left aileron roll. Then it just flips on it's left side and does a horizontal outside loop as if you've only flicked the aileron and then applied full down elevator. I'm not sure if it's a flight model issue, or just something about the way this aircraft actually flew (too much torque and not enough elevator?).
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
Thank you for this gift, Ted! I waited and hoped for a good D.III a long time. One question: on both versions, the skin on the wings and the nose (viewed from the cockpit) are so bright that they turn almost completely white. The colors completely disappear. I do not have this issue with other planes.
I really hope that we can fly her in OFF/WOFF one day.
That can happen if you have shine enabled in the shader xml, and with some of the earlier versions of AnKor's d3d8.dll.
It can be fixed with a minor hex edit of the m3d file.
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
Hello Major,
Thanks for this useful information. Can you perhaps point me to a tutorial or so in which the modifications are explained?
Best regards,
Stickshaker
http://www.sim-outhouse.com/sohforum...dge-base/page3
Post #58/
I use XVI32 as my editor http://www.chmaas.handshake.de/delph...2.htm#download
Setting the width to 36 columns makes everything line up so it's easy to see the correct section of the m3d file to edit.
US Army, Major, Ret.
Service To The Line,
On The Line,
On Time
US Army Ordnance Corps.
Thanks, Major, I'll give it a try.
Members who have read this thread: 0
Posting Permissions
Reply With Quote
Bookmarks