P3D Screenshots Here

[Dangerous Beans]

Hey Bruce
Is the C337 working OK for you
It only works intermittently in P3D for me, more often than not P3D will crash with a fatal error when I try to load it.
When it does load none of the VC switches are clickable.

[Bruce Thompson]

Hey Bruce
Is the C337 working OK for you
It only works intermittently in P3D for me, more often than not P3D will crash with a fatal error when I try to load it.
When it does load none of the VC switches are clickable.

Hi,

It seems to be working fine in Prepar3D, all I did was copy it over from FSX and I also copied all the Gauges from the Gauge folder and all the effects too.

[VCN-1]

I have trouble with the 337 also. CTD from the VC.

VCN-1

[Lionheart]

Hey Bruce
Is the C337 working OK for you
It only works intermittently in P3D for me, more often than not P3D will crash with a fatal error when I try to load it.
When it does load none of the VC switches are clickable.

I am 99% sure that if you are having intermittent operation of VC switches, its because you are floating too far back in the VC and the seat polygons are blocking you. I know it sounds crazy.

If you are using TrackIR with that other system, trying moving backward in your seat, reset the view, then sit regularly. This moves you forward a couple of inches.

Also, since its intermittent, I think head latency is also pulling you back into the seat polygons. Again, readjust the view point in the aircraft.cfg file and set it .10 or .20 forward (add that on in positive direction, such as 1.2 will now be 1.3, -1.3 will now be -1.2, etc). Then check in FS/P3D and see if that cures it.



Bill

[billythe]

i am curious seeing if fs water configurator works with prepar3d...actually i don't like water in prepar3d

[Lionheart]

i am curious seeing if fs water configurator works with prepar3d...actually i don't like water in prepar3d

To me, it appears more '3D', and that I like. From altitude, it looks like wave swells moving along in the wind.

[CG_1976]

The Captain Sim V0.9 leaving YZF for the moring YEG run. Good Morning Prepar3D and REX.

[billythe]

rex water looks nice.

[CG_1976]

rex water looks nice.

That's Prepar3D's waters. I only use the REX clouds and Wx Engine.

[norab]

Here is the Vertigo P-36



and please be advised that Pablo diaz's Hi def clouds work fine in Prepar3D

[Lionheart]

The Captain Sim V0.9 leaving YZF for the moring YEG run. Good Morning Prepar3D and REX.

Great screenshots!

Love the classic 737 by CS! I remember those smaller diameter engines, the 200 version fuselages. I cant believe how far the three seven has come.


Bill

[CG_1976]

Yikes!! AMD Six Core going wild in Prepar3D with CS737 and REX Clouds.

[Lionheart]

Here is the Vertigo P-36



and please be advised that Pablo diaz's Hi def clouds work fine in Prepar3D

Norab,

I didnt see your post. I was writing when you posted. Great screenshots man! Sharp looking bird.

[Lionheart]

Yikes!! AMD Six Core going wild in Prepar3D with CS737 and REX Clouds.

6 Core!!!!



Must be nice...

[CG_1976]

Actually it's not badly priced http://www.newegg.com/Product/Produc...82E16819106010
My other
AMD system is a 8 core and almost ready to operate. Just saving money for it's Nvidia card and extra ram. http://www.newegg.com/Product/Produc...82E16819106010