Inspired by A2A Piper Cherokee - Page 14
Contribute Now
Goal amount for this year: 10000 USD, Received: 9,555.00 USD (96%)
Welcome Back, Unregistered     Today's Date:       Current Time: 

Please Support the SOH "2020 Charter Membership Drive"




Accepted Payment Types

Page 14 of 14 FirstFirst ... 467891011121314
Results 326 to 337 of 337

Thread: Inspired by A2A Piper Cherokee

  1. #326
    final and complete..I think





    the radio masts are made from guitar strings..it's kind of a theme now I guess
    enter..the Sandman

  2. #327

  3. #328
    I've been working sporadically, as time allows, on the Dumas Lockheed Air Express...just haven't taken any pictures of it.
    I've also received the dummy Wasp engine from Williams Bro's and have it basically assembled and I have gotten the decal sheet for the Roscoe Turner piloted Gilmore aircraft from Callie Graphics. She has done a beautiful job on them and I can't wait to see this model wearing them.
    I should be able to post some progress shots soon - but I'm afraid there isn't much to show yet..still infilling the fuselage (around 30% complete)
    If you want to see some of that and can't wait for the still shots here you can look at the channel 'Heywood Planes' on youtube
    So much to do - so little time lol
    enter..the Sandman

  4. #329
    This is the aircraft I am currently working on - in this exact livery..I hope
    enter..the Sandman

  5. #330
    current status of the Dumas Lockheed Air Express - Gilmore Oil sponsored aircraft...

    this represents about 20% of the total effort - maybe less than that

    enter..the Sandman

  6. #331
    some progress to show..






    the cowling is almost done - just have to detail and then reinsert the vacu-formed engine facia and it'll be ready for paint prep.

    The main LG wheel pants are ready to prep for paint but the fuselage still needs most of its infill work yet before it can be sanded and spackled to proper shape.

    You can see where I have installed the magnet into the firewall. This will secure the Williams Bro's dummy engine for the version of this aircraft before the NACA cowling was added. Then when I want the cowling version I'll just remove the dummy motor and install the cowling with its engine facia for that look. All because the Williams Bro's dummy motor won't fit into the cowling without cutting, hinging, cursing and swearing..
    enter..the Sandman

  7. #332
    fuselage infill is complete. I have applied the spackle and sanded her down to a fairly smoooth condition - and added the forward landing gear struts and wheels. The next step will be to add the trailing LG struts and then the tailwheel assy. I had to fabricate and install the gear legs prior to paint because of the level of difficulty. So many intersections and variables had to be worked out in order to keep it all fair and square that there just wasn't any other way but to fabricate and install now. should be a hoot to mask and paint that Gilmore scheme now, yeah? lol





    enter..the Sandman

  8. #333
    I should have an update and a few pictures to post later today..
    enter..the Sandman

  9. #334
    tail wheel added - morning sunlight and from the bench




    empennage added along with the fairings and fillets


    enter..the Sandman

  10. #335
    I've just laid up the wing and begun the infill work on it..wont be much to show until that work is done and I can begin to shape and sand it..

    I am also working on the motor(s) for this plane. One will be loose and can be attached magnetically to the firewall - the other will be part of the cowling. Both will need a lot of work done to make them look proper and scale.
    enter..the Sandman

  11. #336
    I hope to be able to post a few update pictures this weekend. I have not been able to work on the project as much as I would like due to other requirements on my time but what there is I will share as soon as possible.
    enter..the Sandman

  12. #337
    I repeated myself here,but great work my friend,I know Iím always saying this but Iím now gathering the supplies to do a 1/25th scale Mack B61 tractor with a tank trailer,but Iím doing it as a private contract water tender for fire suppression.im actually going to do several,single and duel drive tractors,with a full sized (40ft) trailer using a 3D printer trailer depicting the fuel truck from the movie duel,and then 20 ft trailers.some will be ďshow truckĒ finished and at least one dirtied up,and maybe a diorama with some drafting off a small bridge,what I have in mind is a pump trailer,or a pickup with a pump for a bed,or in the bed,that the other water tenders would fill from,Iím thinking of using a 55chevy camio kit and scratch build a body.ive finally have my boat set up so I donít have crap everywhere,so now I can mess it all up with model building stuff,lol.btw the Mackís are all resin kits .

Members who have read this thread: 26

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •