Flight plan error driving me insane

Trying to get TTools to compile,but it gives the same error(the altitude format is bad should be 0 to 1023)on all these entries:

AC#24,DIAFS,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/18:48,040,R,0000,EDMA
AC#25,DMSGB,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/18:58,040,R,0000,EDOI
AC#26,GAPRR,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/19:10,040,R,0000,EGTH
AC#27,DFONL,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/19:15,040,R,0000,EHLE
AC#28,ESCAD,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/17:45,040,R,0000,LFLY
AC#29,PHKHV,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/18:20,040,R,0000,EHGR
AC#30,FEZEJ,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/19:15,040,R,0000,LFPM
AC#40,GVTAL,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/19:20,040,R,0000,EGBW
AC#41,HBCKA,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/16:20,040,R,0000,LSZK
AC#42,DEKUT,50%,WEEK,VFR,6/07:35,030,R,0000,EDST,6/17:00,040,R,0000,EDLP
AC#43,DIAFS,50%,WEEK,VFR,6/06:30,030,R,0000,EDST,6/18:20,040,R,0000,EDTN
AC#44,HBLAQ,50%,WEEK,VFR,6/06:30,030,R,0000,EDST,6/18:30,040,R,0000,LFSB
AC#45,DICDY,50%,WEEK,VFR,6/06:30,030,R,0000,EDST,6/18:02,040,R,0000,EDHE
AC#46,DIRES,50%,WEEK,VFR,6/06:35,030,R,0000,EDST,6/18:07,040,R,0000,EDHE
AC#47,GAORG,50%,WEEK,VFR,6/06:35,030,R,0000,EDST,6/16:20,040,R,0000,EGJJ
AC#48,OKMJN,50%,WEEK,VFR,6/06:35,030,R,0000,EDST,6/16:25,040,R,0000,LKVY
AC#49,OKLKO,50%,WEEK,VFR,6/06:25,030,R,0000,EDST,6/16:15,040,R,0000,LKCM
AC#50,OKCTB,50%,WEEK,VFR,6/06:00,030,R,0000,EDST,6/16:05,040,R,0000,LKTB
AC#51,OKRFG,50%,WEEK,VFR,6/06:00,030,R,0000,EDST,6/16:10,040,R,0000,LKPD
AC#52,DMWZY,50%,WEEK,VFR,6/06:00,030,R,0000,EDST,6/16:25,040,R,0000,LKPR
AC#53,OYBGT,50%,WEEK,VFR,6/05:45,030,R,0000,EDST,6/17:00,040,R,0000,EKBO
AC#54,OYFAW,50%,WEEK,VFR,6/05:50,030,R,0000,EDST,6/17:20,040,R,0000,EKSW
AC#55,FOATC,50%,WEEK,VFR,6/05:30,030,R,0000,EDST,6/17:23,040,R,0000,LFLY
AC#56,OOCJS,50%,WEEK,VFR,6/05:15,030,R,0000,EDST,6/18:35,040,R,0000,EBBL
AC#57,PHOTA,50%,WEEK,VFR,6/05:00,030,R,0000,EDST,6/18:50,040,R,0000,EHGR
AC#58,DEFTX,50%,WEEK,VFR,6/07:15,030,R,0000,EDST,6/18:52,040,R,0000,EDFM
AC#59,DEQXL,50%,WEEK,VFR,6/07:15,030,R,0000,EDST,6/19:00,040,R,0000,EDLP
AC#60,N46557,50%,WEEK,VFR,6/07:30,030,R,0000,EDST,6/18:58,040,R,0000,EDLN
AC#61,DFMCA,50%,WEEK,VFR,6/07:00,030,R,0000,EDST,6/19:05,040,R,0000,EDFM
AC#62,FGKJT,50%,WEEK,VFR,6/07:00,030,R,0000,EDST,6/15:55,040,R,0000,LFLV
AC#63,FGGKK,50%,WEEK,VFR,6/07:00,030,R,0000,EDST,6/16:07,040,R,0000,LFBR
AC#64,N473DC,50,WEEK,VFR,6/07:00,030,R,0000,EDST,6/19:05,040,R,0000,EGSX

It's highlighting the first "R"just behind the first altitude designator(030)in red as though that is the problem.
I've done another set in exactly the same format and it's swallowed that no problem.
It's driving me absolutely nuts trying to figure it out because I just cannot spot the problem.

There are some elements of TT that are still a mystery to me, but have you try'd subbing the R for F

I'm a little rusty on TTools, but have you tried to parse it through something like AIFP? Even if you didn't compile with it, it could probably at the very least verify the error.

When you say another "set," what exactly is different this time around? What have you changed here that would be different? Maybe substituting something one by one can give you a different answer?

Also, I noticed the altitude was "030" for a VFR flightplan. Again, I'm rusty on TTools, but will it let you compile something like that where the altitude doesn't match the flightplan type? For IFR the "030" would be fine, otherwise "035" would be correct for VFR. Don't know if TTools makes you correct that or not, especially if you say it's worked before.

Also, I can't remember if this is a TNG type flight or not. If you use TNG, then you have to use the IFR option or it may not work. With IFR the aircraft will do a low pass then go around. If you have VFR, then the aircraft will land, stop, then take off again. If there isn't enough runway it won't work. I'm not sure if TTools checks for this as well or not.

Hope this helped!

Jorge
Miami, FL

Your FP should look like that:

AC#24,DIAFS,50%,WEEK,VFR,6/05:50,030,6/10:00,030,R,0000,EDST,6/18:48,6/18:48,040,R,0000,EDMA

The bold marked entries are simply missing. It doesn't matter what time your insert. TTools will calculate and set arrival times anyway.

Bernard

Quote:

---

Originally Posted by leuen

Your FP should looks like that:

AC#24,DIAFS,50%,WEEK,VFR,6/05:50,030,6/10:00,030,R,0000,EDST,6/18:48,6/18:48,040,R,0000,EDMA

The bold marked entries are simply missing. It doesn't matter what time your insert. TTools will calculate and set arrival times anyway.

Bernard

---

Of course,of course!!!!!,I haven't put an ETA in!!!

Thanks Bernard.