Overclocking guide

[harleyman]

I have avaible a new overclocking guide hand written by txnetcop.......From the origional Author Graysky..... ( updated and corrected by txnetcop)


Everything you ever wanted to know about OVERCLOCKING GUIDE FOR CORE2DUO and CORE2QUADs

Its large and you need to PM me with your E-Mail address and I will send it to you

Much Thanks To Ted For This....:applause:

[harleyman]

And For All You Power Heads....An Explanition About Ram Timings


http://www.tweakers.fr/timings.html

[kilo delta]

A very useful link here too.......... http://www.sim-outhouse.com/sohforums/showthread.php?t=11983 :ernae:

Fantastic Kilo Delta.........Thanks for this link....Hope you don't mind me dropping this in here....Harleyman Great job Mo......Many thanks from us all....

[SirBenn21]

Hi I've just requested guide.

Using Prime95

I can get my @9550 to run in Windows @ 4.0 GHz, but Crash Core 2 at 10 minutes so I've decided to run @ 3.8 GHz.
Core 2 stops after 2 1/2 hours and Core 1 stops at 8 hours. I haven't run longer than that.
Below are my settings.

3.8 ghz -

JumperFree Configuration Settings:

AI Overclock tuner: Manual
CPU Ratio Setting: 8.5
FSB Strap to North Bridge: auto
FSB Frequency: 450
PCI-E Frequency: 101
DRAM Frequency: 969
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual

1st Information :

CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : AUTO
Row Refresh Cycle Time: auto
Write Recovery Time: AUTO
Read to Precharge Time: AUTO

2nd Information :

READ to WRITE Delay (S/D): AUTO
Write to Read Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ Delay (S): AUTO
READ to READ Delay (D): AUTO
WRITE to WRITE Delay (S): AUTO
WRITE to WRITE Delay (D): AUTO

3rd Information :

WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: Disabled
DRAM Read Training: Disabled
MEM. OC Charger: Auto
AI Clock Twister: Auto
AI Transaction Booster: Auto

CPU Voltage: 1.2625
CPU GTL Voltage Reference (0/2): AUTO
CPU PLL Voltage:
FSB Termination Voltage: 1.24
DRAM Voltage: 2.08
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: 1.2
PCIE SATA Voltage: 1.50

Load Line Calibration: Enabled
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : Auto
NB Clock Skew : Auto
Cpu margin enhancement : OPTIMIZED

Advance CPU Settings
CPU Ratio Setting: 8.5
C1E Suppport: Disabled
Max CPUID Value Limitff
Intel® Virtualization Tech: on
CPU TM Function: ENABLED
Execute Disable Bit: ENABLED

All cores don't exceed 55 C

Thanks

Ben

[stansdds]

You might want to play with the voltages a bit more since you are experiencing crashes. Granted, 3.8 GHz from a 2.83 GHz CPU is a hell of a good overclock, but others have done the same and with 24 hour stability.

[SirBenn21]

Okay here is an update.

Messed around with a lot of settings with no real improvement until I set everything as stated above, but changed only one setting

DRAM Frequency: 969 I now have at DRAM Frequency: 1096.

Core 2 now ran though(10 Hours), but core 1 still stopped at 8 hours. :confused:

Man this takes a long time to test!

What's considded a stable OC?

Ben

[stansdds]

Depends upon your standards. For me, at least 12 hours. I think 24 hours is pretty much the gold standard.